 |
Programmable Isolated DIN Rail Thermocouple & PT100 Intelligent Math Function Transmitter Easy to use Easy and Calibrate ! |
Feature: The IsignalCon Transmitter has 2 inputs and caters for simple maths manipulation of one or both using a formula and can be set to have a variety of analog outputs as shown below.
Feature: Configure without power or load connected, Ideal for configuration in the workshop before installation.
Feature: All models are ISOLATED on input !
Feature: Configurable inputs and range.
IsignalCon ISC-S has 2 inputs and one analog output.
IsignalCon ISC-D has 2 inputs and 2 analog outputs.
IsignalCon ISC-C has 2 inputs and 1 x analog and 1 RS485 comms port.
These can be configured using our "iSignalTrans" software on your PC/notebook or our dedicated handheld programmer using the special URC-1020 USB interface cable. "iSignalWin" is our user-friendly calibration software. The latest version can be download free from our website.
The
transmitter can be calibrated in the workshop without connection to any wiring
or power source.
The
formulae 
is avaliable
to mix or manipulate one or both the 2 inputs if you choose.
• The formulae can only be used on one output channel on
the ISC-D and ISC-C units.
• PV1 and PV2 are measuring value of input 1 and 2.
• A, B and C are constants set by the user.
• In order to make the formula versatile you can disable the root part
of the equation and simply use the arithmetic functions should you choose.
Using
the ISC-C module allows you to network both input signals on a RS485 network
for use in a PC or PLC.
Input (Note 4) |
Thermocouple (T/C) : industry standard thermocouple types J, K, T, E, B, R, S, N, C (ITS-90). |
| Pt100: Excitation 180uA. 2 or 3 wire connection (ITS-90 a =0.00385). | |
| Voltage: -60 mV dc to 60 mV dc or -10Vdc to 10V dc. | |
| Current : 0-24 mA dc | |
| Accuracy | Refer to Table 1.Input Signal |
| A/D Resolution | 16 bits |
| Input Sampling Rate | < 200 ms |
| Output | Current output milli amp into resistive load max 600 ohms max. Typically 4~20 mA or 0~20 mA etc |
| Analog voltage output 0~50 mV or 0~10 Vdc into resistive load of high impedence. | |
| Output Resolution | 0.6 µA (15 bits) |
| Output Responce Time | <200 mS |
| Power supply | DC 12 to 35 V, |
| Humidity | 0 to 90% RH |
| Operating temperature | -40 to 85 deg C |
| Galvanic isolation | 4 KV 1min. between input and output |
| Common Mode Rejection Ratio (CMMR) | >80 dB |
| Electromagnetic Compatibility | En 50081-2, En 50082-2 |
| Dimension | 75mm (W)x 87mm (H)x 18.5mm (D) |
-
Calibration is done using a USB port on your PC and a special USB cable that includes an interface adaption. This cable is avaliable from us and it's code is URC-1020.
-
Selection of mV, V or mA inputs involves on-board dip switch selection. The input signals of the ISC are divided into three groups. To change input signal from one group to another. the DIP switch have to be set accordingly. These are ...
1. RTD( pt100) , T/C ( J,K,T,E,B,R,S,N,C) and mV ( -60~60mV)
2. mA ( 0~24mA)
3. V ( -10~10V )
-
We are in the process of developing a hand held programmer to facilitate simple configuration and input selection.
-
Note on mains power source...For example, a 24Vdc power source, the Max. load of 0~20mA will be (Vpower - 12)/ 0.02 = ( 24-12 )/0.02 = 600 ohms. So, a lower power supply results in lower load capability.
|
2
YEAR WARRANTY
back
to top
Back
to Main Page
QIS is the UK sole importer and European outlet
for the VERTEX product
We provide full sales , technical and after sales service for this product